Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Glendale Homeowners
A gate that won’t open leaves you parked in the street, and a gate that won’t close leaves your driveway open to anyone. Gate repair in Glendale means finding out why that’s happening – a dead operator, a bound hinge, a control board that took a power surge, a slide track full of grit – and fixing it the same day whenever the parts allow. Our technicians have up to 13 years of experience and work only on gates, including automated and electric systems, so the operator you already have is one we’ve likely diagnosed before.
We answer 24/7, and fast dispatch from 7am to 7pm runs Sunday through Friday. For a gate that won’t secure, call (888) 853-9043 and we’ll get a technician headed your way. Whether you have an older Mighty Mule swing operator or a LiftMaster system on a newer install, we repair the brand that’s actually installed instead of working around it. Estimates are free, and the price is quoted and agreed before any work starts.
Driveway Gate Repair
Driveway Gate Repair covers the gate at the mouth of your property, the one vehicles pass through, and it’s what we handle most often in Glendale. You need it when the gate drags, stops halfway, opens on its own, or won’t respond to the remote at all. A small failure on a driveway gate turns into a closed-in car fast, which is why we treat sagging hinges and worn operators as urgent rather than something to schedule later. Typical driveway gate repair in Glendale runs $150 to $650 depending on whether the fix is mechanical or electronic. Our free estimate tells you which side of that range you’re on before we touch anything.
Hinges, Posts, and Swing Arms
Most driveway swing gates that fail have a hinge or a post problem underneath the obvious symptom. A hinge that’s worn past its bushing lets the gate sag, and a sagging gate strains the operator until it quits. We check post integrity and frame twist before we ever adjust the operator, because the electronics can’t compensate for a gate that’s out of true.
Operator and Remote Diagnostics
A gate that ignores the remote can have a dead battery, a failed receiver, a bad limit switch, or a control board that’s given up. We test each link in that chain rather than swapping parts on a guess. If the operator is a brand we know well, the diagnosis is faster because we’ve seen how that unit handles surges and wear.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Welding
Gate Welding is the structural side of gate repair – broken pickets, cracked hinge plates, split frames, and rust-throughs that no amount of adjustment will fix. You need it when the gate has taken an impact, when a weld has failed at a stress point, or when the frame has rusted thin enough that it flexes. Our technicians weld on-site where the material and access allow, and we match the repair to the metal so the fix looks like it belongs. Typical gate welding in Glendale runs $200 to $700 depending on how much fabrication is involved. A written estimate sets the final price.
On-Site Structural Repairs
A gate that’s still hanging can often be repaired where it sits, which saves you the cost and delay of a full removal. We brace the gate, cut out the failed section, and reweld the joint with the frame held square. Small picket and frame damage is usually a straightforward on-site job.
When a Weld Can’t Save the Gate
Heavy rust on a frame, repeated failures at the same joint, or a post that’s pulled loose from its footing can push a repair past the point of good money after bad. We’ll tell you plainly when a repair won’t hold. In those cases we quote a replacement through our gate installation work, and you decide.
Commercial Gate Repair
Commercial Gate Repair applies to vehicular access gates at businesses, apartment properties, and small commercial lots where the gate controls who gets in and when. You need it when an access gate is stuck open, when a tenant or delivery driver can’t get through, or when the loop detector has stopped sensing a vehicle. These systems run harder than residential gates and fail differently, so we service the commercial-grade equipment – FAAC, BFT, and DoorKing among them – that a general repair shop often turns away. Typical commercial gate repair in Glendale runs $250 to $900 depending on operator complexity and parts. Work is measured and scheduled, and the price is agreed in writing before it starts.
Access Control and Loop Detectors
A gate that stays open usually has a loop detector reading a phantom vehicle or a control board that’s lost its logic. We test the loop, the receiver, and the board in sequence so we’re replacing the actual fault, not a part that’s fine. Access components get the same treatment – tested, not assumed.
Keeping a Property Secure During Repairs
An open commercial gate overnight is a real security problem, so we prioritize getting the gate back to a closed and locked state first, then finish the repair. Where a full fix needs an ordered part, we secure the gate in the meantime. You won’t be left with an open access point while you wait.
Iron Gate Repair
Iron Gate Repair covers solid iron gates and iron-framed entries that have gone stiff, misaligned, or loose at the hinge. You need it when the gate scrapes the ground, when bolts have worked loose, or when the latch no longer meets the strike cleanly. Iron is heavy, and that weight puts stress on hinges and posts that lighter materials never see – which is exactly where these gates start to fail. Typical iron gate repair in Glendale runs $180 to $600 depending on hinge and post work. We confirm the cause and the price on a free estimate before any repair begins. For a closer look at what drives that cost, see our Glendale Gate Repair guide to local estimates.
Hinge and Latch Alignment
An iron gate that won’t close right usually has a hinge out of alignment or a post that’s shifted. We reset the gate, rehang it if needed, and align the latch to the strike so it closes without force. Getting this right stops the recurring problem where a gate “fixes itself” for a week and then fails again.
Rust, Paint, and Protective Coating
Bare iron rusts, and rust eats weight-bearing metal faster than it looks. We treat rusted spots at the point of repair and recommend a protective coating afterward. Coating the repaired area is what keeps the gate from coming back to us a season later.
Sliding Gate Repair
Sliding Gate Repair handles gates that travel along a track rather than swinging, and it’s a different set of failures entirely – rollers, tracks, and the guides that keep the panel from pulling off line. You need it when the gate jumps the track, when the motor runs but the gate doesn’t move, or when the panel has shifted and grinds. A slide gate that comes off its track is heavy and dangerous, so stop using it and call rather than pushing it back by hand. Typical sliding gate repair in Glendale runs $200 to $750 depending on track, roller, or operator work. For gate issues we don’t cover here, our team serving gate repair in Rose Hills can point you the right way.
Track, Roller, and Guide Work
Most slide gate problems trace to a worn roller or a track that’s bent or fouled. We replace rollers, straighten or reset the track, and check the upper guide so the panel stays on line under load. A gate that tracks true puts far less strain on the operator.
Slide Operator Alignment
The operator has to line up with the gate travel, and a panel that’s drifted will fight the motor until something breaks. We align the operator to the actual gate path rather than forcing the gate to the operator. That small difference is what keeps the gate running without repeat visits.
Wrought Iron Gate Repair
Wrought Iron Gate Repair is for decorative and ornamental iron gates where the look matters as much as the function, and where loose scrollwork or a sagging arch can’t just be braced and forgotten. You need it when pickets are loose, when the gate has developed a lean, or when rust has set into a decorative joint. These gates are often older and made of thinner stock, so the repair has to respect the original design instead of grabbing whatever metal is on hand. Typical wrought iron gate repair in Glendale runs $180 to $650 depending on the amount of fine work. We tell you honestly whether a repair or a replacement makes more sense.
Restoring Loose and Bent Detail Work
Scrollwork, finials, and decorative joins take the first hit when a wrought iron gate is bumped or leaned on. We reshape bent detail and reweld loose joints so the pattern reads correctly again. Matching the original profile is the goal, not just getting metal back on the frame.
Rust Treatment on Ornamental Iron
Wrought iron with layered paint hides rust until it’s through the metal, so we inspect at the joints and low points where water collects. We treat the rust found at the repair and recoat the area. Looking past the surface rust is what prevents a repeat failure.
Metal Gate Repair
Metal Gate Repair covers steel, aluminum, and mixed-metal gates that have bent, seized, or come loose at the frame. You need it when a tubular frame has taken a hit, when bolts have seized, or when a gate has been forced and the latch has torn free. Aluminum and steel fail differently, so the repair has to match the material – aluminum bends and cracks where steel deforms and shears. Typical metal gate repair in Glendale runs $150 to $600 depending on material and severity. We inspect, quote, and get your agreement before any repair starts.
Frame Straightening and Re-Bracing
A bent frame throws off the whole gate, from the latch to the operator. We straighten the frame and add bracing where the original design left the gate weak. Getting the frame true again is what makes the rest of the repair last.
Bolt, Bracket, and Fastener Repairs
Seized bolts and loose brackets are common on gates exposed to weather and years of use. We extract, replace, and torque fasteners back to a secure hold. A bracket that’s held tight stops the wobble that leads to a bigger failure.
Wood Gate Repair
Wood Gate Repair handles gates built of wood or wood with metal framing, where the failure usually starts with moisture and the wood’s own movement. You need it when the gate sags, when boards have warped or split, or when the frame has pulled apart at a joint. Glendale’s dry stretches and rainy months both work on wood, and a gate that swells in a wet spell and shrinks later ends up with loose fasteners. Typical wood gate repair in Glendale runs $150 to $600 depending on how much wood and framing work is involved. Our estimate tells you what’s actually needed. Property managers in gate repair in North El Monte rely on us for the same reason: we handle the wood and the hardware together.
Sagging, Racking, and Frame Repairs
Wood gates sag when the frame racks out of square, and no hinge adjustment fixes that. We re-square the frame, reinforce the joints, and rehang the gate so it swings clean. Addressing the frame instead of the symptom is what keeps a wood gate working through the seasons.
Rot and Warped Board Replacement
Rot at the bottom rail and warped boards are the usual culprits behind a wood gate that drags or won’t close. We cut out the damaged sections and replace them with matched stock. Sealing the repair helps the gate handle the next wet spell better.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We work on the brand you already have, and that means we service nine major gate automation names rather than trying to force a workaround onto an unfamiliar system. That includes LiftMaster equipment, where we know how the operator responds to wear and where the control board tends to give out first. It includes FAAC, a commercial-grade line where diagnosing the operator means understanding the logic it’s built on. And it includes Mighty Mule and Elite on the residential and professional tiers, where the systems are simpler but the failure points are just as specific.
Between those we also cover BFT, Linear, Viking, Ghost Controls, and DoorKing, spanning residential gates to high-security commercial access systems. Owning the diagnostic instead of guessing at it is the whole point of a gate-only shop. Whether you have a Mighty Mule on a suburban driveway or a DoorKing controlling a commercial lot, or any other make, we can help. If your gate needs a new operator entirely, we install automation from these brands too.
Signs You Need a Pro Right Now
- The gate won’t close or stay closed. A gate that reverses at the last inch or won’t latch leaves your property open. That’s often a limit switch, a safety sensor, or a strike out of alignment, and none of those fix themselves. Call us rather than propping it shut.
- The operator runs but the gate doesn’t move. A motor that hums or cycles with no movement usually means a broken gear, a sheared pin, or a drive that’s failed. Running it further can burn out the motor. Shut the power off and have it diagnosed.
- Grinding, scraping, or a jump on the track. Noise on a slide gate points to worn rollers or a bent track, and a gate that’s starting to come off line is dangerous. Stop using it and get it looked at the same day.
- Odd behavior from the remote or keypad. A gate that opens part way, opens on its own, or ignores the remote has an electronics fault. Intermittent behavior is the hardest to chase without test equipment, which is exactly what we bring.
- A gate that’s visibly leaning or dragging. A sag here, a gap at the latch there, and the whole gate is straining its operator. That’s how a small hinge fix becomes a full rebuild if you wait.
Our Process, Step by Step
- 1
Call and describe the gate. We ask what the gate is doing, what brand the operator is, and whether it’s manual or automated. That short conversation tells us what to expect before a technician arrives, and how to prioritize a gate that isn’t securing your property.
- 2
Free on-site diagnosis. We inspect the gate itself, the frame, the hinges or track, the operator, and the wiring. We use a multimeter and, where the operator supports it, a diagnostic readout to test the control board and receiver rather than swapping parts.
- 3
A clear written estimate. You get the diagnosis in plain language and a price for the work, quoted and agreed before we start. No surprises when it’s done, and no fee to get the estimate.
- 4
Repair or replace, honestly. If a repair makes sense, we do the repair. If the gate or operator has reached the point where a fix won’t last, we’ll say so and quote a replacement instead.
- 5
Test and walk-through. Before we leave, we run the gate through a full open and close cycle, test the remotes and access components, and confirm with you that it’s working the way it should.
How Much Does Gate Repair Cost in Glendale?
A typical gate repair in Glendale runs $150 to $900, with most residential repairs landing in the $200 to $450 range. The wide spread comes down to what’s actually broken and how much of it. A hinge or latch adjustment sits at the low end. A failed operator, a bent slide track, or a control board replacement pushes higher. Commercial gate repair runs higher than residential for the same reason commercial equipment costs more to service – more complex logic, heavier components, and access systems to test alongside the gate.
What affects the price most is whether the job is mechanical or electronic, whether parts are standard or need ordering, and whether the gate itself needs to come off its hinges or track to do the work. A gate that’s simply out of alignment is quick. A gate that’s been forced, bent, and welded badly by a previous attempt takes more time to put right. We check the root cause before pricing, so you’re not paying for a repair to a symptom.
What’s included in the free estimate: the on-site inspection, the diagnosis, and a clear price for the repair in writing. What we don’t do is quote a number over the phone and surprise you at the invoice. The written estimate sets the final price, and it’s quoted before any work starts. Call (888) 853-9043 for an exact quote – estimates are free.
Our Service Area Near Glendale
We repair gates across Glendale and the neighboring communities – North El Monte, Rose Hills, La Cañada Flintridge, La Crescenta-Montrose, Altadena, South Pasadena, San Marino, East Pasadena, and San Gabriel. Dispatch runs from 7am to 7pm Sunday through Friday, and technicians reach most nearby addresses the same day they’re called. Whether you’re a homeowner in Glendale or a property manager with a commercial access gate, one call covers the diagnosis and the fix. Call (888) 853-9043 to book.
Serving Glendale, CA – Our Local Coverage Area
We serve Glendale and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Glendale
Gate repair is the diagnosing and fixing of a gate system so it opens, closes, and secures properly again. That covers the gate itself – frame, hinges, latches, track, and rollers – plus the operator, control board, remotes, and access components on an automated gate. We take the whole system apart in our head to find the actual failure, not just the part that made the noise. Then we quote the fix in writing before any work starts.
Most repairs finish in a single visit, often within two to three hours. Mechanical fixes like alignment, hinge, or latch work are usually quick. Operator or control board replacements depend on whether we have the part for your brand, and commercial systems take longer because there’s more to test. Call (888) 853-9043 and we’ll give you a realistic time when we know the symptoms.
Most gate repairs in Glendale run $150 to $900 depending on the cause and the parts. Mechanical fixes sit at the low end, and operator, control board, or commercial work runs higher. The estimate is free, and the price is quoted and agreed before work begins, so the final bill matches what you were told. Call (888) 853-9043 for an exact quote – estimates are free.
Yes – we service LiftMaster along with FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Working on nine named brands means we diagnose the actual unit installed instead of forcing a generic fix onto a system we don’t know. That includes the control board, remotes, and access components. Call (888) 853-9043 and tell us the brand when you book.
Same-day service is often available in Glendale, depending on the schedule. We answer 24/7, and fast dispatch runs 7am to 7pm Sunday through Friday. A call outside dispatch hours is booked into the next opening. We’re closed Saturday, so a gate that fails over the weekend gets booked for Sunday. Call (888) 853-9043 and we’ll get you on the schedule.
We stand behind our repair work with a satisfaction guarantee – if the gate isn’t working the way we said it would, that’s on us to make right. The written estimate you agree to is the price you pay, and the parts and labor are explained before we begin. Call (888) 853-9043 with any questions about a repair.
Have access to both sides of the gate, clear any vehicles out of its path, and know the operator brand if it’s printed on the unit. Note what the gate actually does – stops halfway, reverses, ignores the remote – because those details speed up the diagnosis. If the gate produces the symptoms, it’s working, so leave it as it is. Call (888) 853-9043 to confirm your appointment.
Schedule Your Gate Repair Service in Glendale Today
A gate that won’t open or won’t secure is a problem we can solve today. Call (888) 853-9043. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday, and it’s closed Saturday. Our technicians have up to 13 years of experience on gates and the brands installed on them. The estimate is free and no obligation, the price is agreed before work starts, and we’ll tell you honestly whether to repair or replace. Let’s get your gate working again.
Written by the team at Glendale Gate Repair.