Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Motor & Opener Cost in Glendale?
Most gate motor and opener work in Glendale runs $450 to $1,900, depending on whether we’re repairing an existing operator, replacing a failed unit, or fitting automation to a gate that’s never had it. A straightforward repair like a control board or remote receiver usually lands at the low end, while a full opener replacement with new wiring and safety loops sits at the high end. We give you a written estimate before any work starts, so the number you see is the number you pay.
- Standard answer: gate motor and opener pricing in Glendale typically falls between $450 and $1,900.
- Repairs (motors, boards, remotes, access components) usually cost less than replacements.
- Residential-grade and commercial-grade systems price very differently, and we work on both.
- Estimates are free and the written estimate sets the final price.
Glendale properties run the full range: hillside homes off Chevy Chase Canyon with steep driveways, mid-century houses near Adams Square with narrow single-car gates, and small commercial lots along Brand Boulevard with vehicular swing gates. Each one puts different demands on a motor, and that’s the first thing we look at when we price a job. Call (888) 853-9043. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Gate Motor & Opener Cost Breakdown (2026)
Here’s how the numbers typically break down for a gate motor and opener job in Glendale. Every gate is different, so treat these as estimate ranges, not fixed quotes. The written estimate after we see your gate is what governs the final price.
| Job type | Typical estimated range | What’s usually included |
|---|---|---|
| Diagnostic and repair of an existing opener | $450 – $780 | On-site diagnosis, motor or board repair, recalibration, testing |
| Control board replacement | $380 – $650 | New board, rewiring as needed, safety reversal test |
| Motor replacement (residential swing or slide) | $650 – $1,150 | New operator unit, mounting, travel and force limits set |
| Opener replacement (commercial-grade unit) | $1,100 – $1,900 | Heavier-duty operator, control wiring, loop or safety sensor hookup |
| Remote and receiver work | $120 – $320 | New receiver, programmed remotes, keypad pairing |
| Safety loop and photo-eye installation | $250 – $550 | Loop detector or photo-eye pair, wiring, obstruction testing |
| Full automation of a manual gate | $950 – $1,900 | Operator, wiring, safety devices, remote setup, full testing |
What pushes a job toward the high end? A commercial-grade operator like FAAC, BFT or DoorKing costs more than a residential unit from Mighty Mule or Ghost Controls, and that’s mostly in the equipment. Heavier gate panels need a stronger motor, which means a higher price. Longer runs of underground wiring for a driveway gate add labor. On the other side, a simple repair on an operator that’s already wired and functioning usually comes in well under $800. We work on the brand you already have, whether that’s LiftMaster, Linear, Viking, Elite or any of the commercial systems, so there’s no guesswork about parts or procedures.
What Affects Gate Motor & Opener Pricing in Glendale
Pricing isn’t a flat menu. Here are the six things that move the number most on a Glendale gate job.
- Gate type and weight. A single swing gate on a residential driveway and a wide vehicular slide gate on a commercial lot need very different operators. Heavier panels demand more motor torque, and that’s a genuine cost difference, not padding.
- Brand and system tier. Residential-grade brands (Mighty Mule, Ghost Controls) and professional-tier brands (Viking, Elite, Linear) price differently on parts. Commercial systems like FAAC, BFT and DoorKing sit at the top of the range because the hardware is built for heavier duty cycles.
- Wiring and power. If the gate is far from the power source, running conduit and wire adds to the job. If there’s already a working circuit and control wiring in place, you save on labor.
- Safety devices. Photo-eyes and loop detectors aren’t optional on an automated gate, and installing them properly takes time and wiring. Adding or replacing them is a real line item.
- Access control. Keypads, intercoms and entry systems tied into the operator have their own cost and their own diagnosis. We handle these alongside the motor, so they’re priced in the same visit rather than as a separate trip.
- Property access and hillside conditions. Some Glendale gates sit on steep driveways where the gate has to travel on a grade. That sometimes calls for a different operator model or a different mounting approach, both of which affect cost.
The quickest way to narrow the range for your specific gate is to walk the property with us. Call (888) 853-9043 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Repair or Replace: Which Gate Opener Makes Sense?
This is the question we get most, and the honest answer depends on three things: the age of the operator, the cost of the failed part, and whether the gate itself is still solid.
If the motor is sound and the failure is a board, a receiver, or a remote that won’t pair, repair almost always wins on cost. A $400 to $600 board replacement on an operator that’s otherwise healthy beats a full replacement every time. If the motor has failed, the control board is failing alongside it, or the unit is an older model where parts are getting hard to source, replacement is usually the smarter money. And if the gate itself is worn out (sagging hinges, warped framing), a new opener won’t fix a gate that’s physically struggling; in that case we’d tell you to address the gate first, and we handle Glendale gate repair as part of the same visit.
We give you a straight recommendation on repair versus replace. If repairing it is the sensible call, we’ll say so. If replacing it saves you money over the long run, we’ll show you why.
How to Save on Gate Motor & Opener in Glendale
There’s no magic discount here. But there are a few practical ways to keep the number down without cutting corners on a system that controls access to your property.
- Get the diagnosis right the first time. A gate that “won’t open” can be a dead motor, a bad receiver, a misaligned limit switch, or a safety device tripping. Chasing the wrong part is the most common way people spend twice. We diagnose first, then quote.
- Fix small issues before they compound. A remote that only works up close, a gate that reverses on its own, a motor that strains at one end of travel. Each of these is usually a modest repair. Left alone, they wear out the motor and drive up the bill.
- Bundle access-control work into the same visit. If you want a keypad added or an intercom tied in, doing it while we’re already on-site is cheaper than a second trip.
- Keep the gate itself in shape. Hinges, rollers and tracks that are aligned and lubricated let the motor work less hard. A motor that fights a dragging gate burns out faster.
- Match the operator to the job. Over-buying a commercial-grade operator for a light residential gate wastes money. Under-buying a residential unit for a heavy vehicular gate means it fails early. We’ll size it right.
And the estimate itself is free. There’s no charge to have us out to look at the gate and tell you what it needs. Call (888) 853-9043 to book one.
Why a Gate-Only Specialist Prices the Job Differently
There’s a reason we can give you a useful number over the phone and a firm one on-site: gates are all we do. We don’t split our attention between gates, garage doors, fences and general handyman work. That focus means two things for your price. First, we recognize the operator brand on sight, so we’re not guessing at parts or procedures. Second, we know which repairs are worth doing and which replacements will actually last, so you’re not paying for work that doesn’t solve the problem.
We work on the brand you already have, across the systems Glendale properties actually run: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule. That covers everything from a residential Mighty Mule or Ghost Controls unit on a backyard gate to a commercial DoorKing or BFT operator on a vehicular gate at a small commercial property. Our technicians have up to 13 years of experience, and that’s applied to the specific brand at your address, not a generic approach.
If you’re weighing automation for a gate that’s currently manual, the calculus is different. A manual gate that’s already installed can be automated with an operator, wiring and safety devices, and that usually lands in the $950 to $1,900 range for residential setups. We handle the full arc: repair, electric repair and new installation. So if a gate system is beyond saving, we’re the same vendor for the replacement. No second company, no handoff, no re-diagnosis.
Electric Gate Motor and Opener Work We Handle
Most of the gate motor calls we get in Glendale fall into the electric and automated category, and that’s where a general repair service usually turns around and leaves. We stay.
- Motor and operator repair and replacement, residential and commercial
- Control board and circuit board diagnosis and replacement
- Remote and receiver programming, keypads
- Loop detectors and photo-eye safety devices
- Access control components tied into the operator
- Full automation of a manual swing or slide gate
- New opener installation, sized to the gate
Diagnostic to done, in one visit where the parts allow. If we need to source a specific brand component, we’ll tell you up front rather than leave you guessing.
A Quick Note on Safety
A gate operator carries real electrical risk, and the moving panel is heavy enough to cause serious injury if something goes wrong. We don’t recommend homeowners open the operator housing, touch the wiring, or adjust the force and limit settings themselves. Those settings control how hard the gate pushes and when it reverses, and getting them wrong can defeat the safety devices. Leave motor and control work to a trained technician and keep the area clear when the gate is moving. It’s the same reason we test every safety device before we call a job done.
FAQs – Gate Motor & Opener Cost in Glendale
How much does a new gate opener cost in Glendale?
A new gate opener in Glendale typically costs $650 to $1,900, with residential swing and slide operators at the lower end and commercial-grade units at the upper end. The final price depends on the operator brand, the weight of your gate, and how much wiring and safety hardware the install requires. Call (888) 853-9043 for an exact quote; estimates are free.
Is it cheaper to repair or replace a gate motor?
Repair is usually cheaper when the motor is still healthy and the failure is a board, receiver or remote, often $380 to $780. Replacement makes more sense when the motor itself has failed or the unit is old enough that parts are hard to source, typically $650 to $1,900. We’ll tell you honestly which one makes sense for your gate. Call (888) 853-9043 to get that answer on-site.
What does a gate motor repair cost in Glendale?
A gate motor repair in Glendale typically runs $450 to $780, including diagnosis, the repair itself, and testing. A control board replacement alone usually lands between $380 and $650. The written estimate after we see the gate sets the final price. Call (888) 853-9043 for a free estimate.
Can you automate a manual gate, and what does it cost?
Yes. Full automation of a manual swing or slide gate in Glendale typically costs $950 to $1,900, covering the operator, wiring, safety devices and remote setup. The number moves with gate weight, distance to power, and whether you need access control like a keypad. Call (888) 853-9043 to talk through what your gate would need.
How much does it cost to add safety devices or a new remote?
Adding photo-eyes or a safety loop typically runs $250 to $550, and remote or receiver work usually lands between $120 and $320. These are often the cheapest line items on a gate job, and doing them while we’re already on-site saves you a second visit. Call (888) 853-9043 for a free estimate.
Do you work on the brand of opener I already have?
Yes. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule operators, so we diagnose the actual system installed rather than working around an unfamiliar brand. That covers residential setups and commercial vehicular gates across Glendale. Call (888) 853-9043 and tell us what you’ve got.
Can you come out today?
We offer same-day service when the schedule allows. Call (888) 853-9043. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
Get a Free Estimate on Your Gate Motor or Opener
Whether your operator is dead, your gate has never been automated, or you just want to know what a repair would cost before you commit, the first step is the same. We come out, look at the gate, tell you what it needs, and give you a written estimate. No charge for the estimate, and the price is set per job so you know what you’re paying before we start.
Call (888) 853-9043 to book your free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Glendale market as of 2026. Glendale Gate Repair offers free estimates – call (888) 853-9043.
Written by the team at Glendale Gate Repair.
What Our Customers Say
"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Dana Norris"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Carmen Mendoza"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Jessica Kim