Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Glendale?
Gate installation in Glendale typically runs $2,400 to $7,800 for a standard residential swing gate, installed and working. A basic manual driveway gate sits at the low end, while a wide automated slide gate with access control lands near the top. The written estimate you get after we look at your driveway is what sets the final price.
What you pay depends far more on the gate than on the hardware box it ships in. A single-panel swing gate on level ground is a different job from a wide slide gate crossing a sloped driveway in the Verdugo foothills. We’ll walk your property, measure the opening, check the soil and slope, and give you a free written estimate before anything is ordered.
Glendale has its own reasons a gate quote moves. Lots in the hills sit on grade changes that shape how a gate has to run, driveways are often narrow, and many properties have an existing pier or fence line that a new gate has to meet. None of that is guesswork once we’re standing in your driveway. We specialize exclusively in gates, so an installation estimate from us covers gate work and nothing else. You can read more about how we work on the Glendale Gate Repair page.
Key Takeaways
- Typical installed price in Glendale: $2,400 to $7,800, depending on gate type, width, and automation.
- Automatic openers and access control are the biggest line items, often 35-50% of a project.
- Slope, soil, and an existing pier that has to be tied in can add cost that doesn’t show up in a catalog price.
- Free written estimate before work begins, with the price set per job.
- Call (888) 853-9043. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Gate Installation Cost Breakdown (2026)
This table shows typical Glendale ranges for each piece of a gate installation. Not every project includes every line. A manual gate on a healthy pier may need only the gate, posts, and hangers; an automated slide gate adds operator, safety devices, and access control. These are estimates, and the written estimate you receive is final.
| Line item | Typical Glendale range |
|---|---|
| Manual swing gate, single panel | $900 – $2,600 |
| Manual double-drive swing gate | $1,800 – $4,200 |
| Slide gate, manual, with track and rollers | $1,600 – $4,000 |
| Ornamental iron or aluminum gate (material and build) | $1,200 – $5,500 |
| Wood or composite gate panel | $900 – $3,200 |
| New posts, piers, and footing work | $600 – $3,000 |
| Automated swing operator (arm or articulated) | $1,100 – $2,800 |
| Automated slide operator | $1,400 – $3,600 |
| Safety loops and photo-eye sensors | $350 – $1,100 |
| Keypad, remotes, and access control | $300 – $1,600 |
| Electrical run to the gate location | $400 – $2,400 |
| Battery backup and solar options on lower-voltage systems | $250 – $900 |
Add the gate, hardware, posts, and any automation together and you start to see where the total lands. A plain manual swing gate on a solid existing pier is the least expensive path. Replace the pier, widen the driveway opening, and automate the gate with a slide operator and safety loops, and the project moves toward the top of the range. Electrical is the line item homeowners most often underestimate – if there’s no power at the gate line, getting it there is real work. Nothing in this table is padded as a fee; the estimate is free and the price is set per job by the written estimate.
This is where gate-only specialization matters. We install and repair gates in Glendale, and when a quote includes an operator, the brand on that operator is a brand we service directly – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. You won’t be handed a system that a general repair outfit shrugs at a year later.
What Affects Gate Installation Pricing in Glendale
Glendale is a city of hills and flat blocks, 1920s bungalows and newer infill, and that variety shows up in gate pricing. Here’s what moves a quote up or down.
- Slope and grade. Lots in the Verdugo hills and along streets off Chevy Chase and Glenoaks often sit on grade changes. A slide gate has to run level even when the grade isn’t, and a swing gate on a slope needs hardware that can handle it. Both take more setup than a flat driveway, and that’s a real line item.
- Driveway width and opening. A single-car driveway in a tight Glendale lot limits how wide a gate can swing or slide. Wider openings mean wider gates, heavier panels, and larger operators. Matching an existing fence line or driveway apron sometimes matters more than the gate itself.
- Existing piers, posts, and walls. Many Glendale properties already have a pier or low wall at the driveway. If it’s sound, it can carry the gate and save money. If it’s old, cracked, or undersized, it has to be rebuilt or replaced, which adds footing and concrete work.
- Manual versus automated. Automation is the single biggest swing in price. An automated system costs more to buy and more to install, because it needs an operator, safety devices, and a power source. It also adds convenience, and for many Glendale homeowners with long driveways, it’s the reason they’re replacing the gate in the first place.
- Access control and entry system. A keypad or remotes are simple. A full entry system with loop detectors, intercom, or vehicle detection adds components and wiring. DoorKing systems are common on multi-unit and small commercial properties in Glendale, and getting the entry side right matters as much as the gate.
- Material and finish. Ornamental iron and aluminum carry a higher material cost than wood or composite but hold up better to the sun and dry summers here. Wood gates cost less up front but need more attention over the years.
One Glendale-specific point: because the area is built up, we often work around an existing driveway apron, a property line shared with a neighbor, and a curb cut that’s already established. That’s just part of setting up the job. A good estimate accounts for it before the gate is ordered.
Manual vs. Automated Gate Installation in Glendale
One of the first decisions in any installation is whether the gate will be manual or automated. Manual gates are simpler, cost less, and have fewer parts to fail. Automated gates add an operator, safety sensors, and a power source, and they need to be installed correctly so the gate stops or reverses when it meets an obstacle.
For a single-car driveway with a short approach, a manual swing gate is often the right call. For a long driveway, a wide slide gate, or a property where someone is getting in and out of a car several times a day, automation earns its cost quickly. Small commercial properties with vehicular access gates usually need automation and access control together, and that’s work we handle directly – DoorKing, FAAC, and BFT systems are part of our regular rotation.
We’ll tell you honestly which one makes sense for your property. If a manual gate will serve you well, we’ll say so. If automation is worth the extra, we’ll show you what it adds and what it costs. Our technicians have up to 13 years of experience, and installation is part of the full arc of what we do – repair, electric repair, and new installation – so you don’t need a second vendor when a gate is beyond saving and a new one makes more sense. For more on our work across the city, visit our Glendale page.
How to Save on Gate Installation
There’s no magic discount in gate work. The savings come from making good decisions before the gate is ordered, not from finding a coupon. A few practical tips:
- Keep your existing pier if it’s sound. Have it checked before you assume it needs replacement. A solid masonry pier in good condition can save the cost of new footing and concrete work.
- Choose the gate type that fits the opening. A gate that’s oversized for the driveway costs more in materials, hardware, and operator capacity. Size the gate to the job, not to a photo.
- Plan the electrical run early. If you’re automating, getting power to the gate location is a line item. Deciding where the run goes before the gate is installed avoids rework and awkward conduit routes later.
- Group the work. If the pier, posts, and gate are all being replaced, doing it as one project is simpler and often less expensive than staging it over months.
- Get a written estimate before ordering. It locks in the scope and the price, and it lets you compare options on paper. If one quote omits the electrical or the safety devices, that’s a sign it isn’t a complete quote.
- Repair before replacing where it makes sense. If the existing gate is structurally sound and only the operator has failed, electric repair is often far cheaper than a new gate. We’ll tell you honestly which one makes sense.
Free estimates are the easiest saving of all. Call (888) 853-9043 and we’ll set up a time to walk your property and give you a written estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Can You Install a Gate on a Slope or Uneven Ground?
Yes. Sloped driveways are common in Glendale, especially in the hills, and gates are installed on them regularly. The key difference is the hardware: a swing gate on a slope needs hinges and an operator that can handle the angle, and a slide gate has to be mounted on a rail system that keeps the panel level even as the ground falls away. Getting the post height and rail adjustment right is most of the work.
Uneven ground also affects how the gate meets the ground when it closes. A gate that clears the ground by too much on one side leaves a gap at the bottom, and a gate that’s too close drags. We set the clearance so the gate operates cleanly across the full travel. If the existing pier or wall isn’t level, we’ll tell you what it takes to bring it into line before the gate is installed.
What Brands Do You Install and Service?
We work with nine gate automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That range matters at installation time because the brand you choose shapes the parts, the remotes, the access control options, and who you call when something needs attention. We’re independent – we’re experienced with these brands and we service them directly, which means we diagnose and repair the actual brand installed, without workarounds or guesswork.
The mix covers both ends of the market. Mighty Mule and Ghost Controls are common on residential driveways and are a good fit for homeowners who want straightforward automation. Viking, Elite, and Linear sit in the professional tier. FAAC, BFT, and DoorKing are commercial and high-security systems, and we handle them on small commercial properties and multi-unit buildings as well as on larger residences. Whatever the brand, we install it and we service it, so you have one place to call for the full life of the gate.
How Long Does Gate Installation Take?
Most residential gate installations in Glendale are a one-day to two-day job. A manual swing gate on a sound existing pier is often finished in a day. A slide gate with a new rail, or an automated gate that needs an electrical run and safety loops, usually spans two days. Larger projects with new piers, custom ironwork, or complex access control can run longer, and we’ll tell you the expected timeline in the written estimate.
The timeline depends on the scope, not on the gate alone. If new concrete is involved, it has to cure before hardware goes on, and that’s a scheduled wait, not a delay we can rush. The best way to get a real timeline is to have your property looked at. Call (888) 853-9043 for a free estimate and we’ll lay out the schedule with the price.
Gate Installation vs. Gate Repair: Which Makes Sense?
Installation is the right call when the existing gate is structurally failing, the opening is being widened, or the property is being upgraded to automation and the current gate can’t carry an operator. Repair is the right call when the gate, posts, and pier are sound and the problem is the operator, the control board, the sensors, or the wiring. Electric gate repair is a core part of what we do, and it’s often far cheaper than replacement.
We’ll tell you honestly which one makes sense. If a repair will get you years of service, we’ll recommend it. If it’s throwing good money after bad, we’ll say so and show you what a replacement looks like. Because gates are our only focus, there’s no reason to push a new gate when a repair will do, and no reason to patch a gate that’s past saving.
FAQs – Gate Installation Cost
How much does gate installation cost in Glendale?
Most gate installations in Glendale run $2,400 to $7,800 installed, depending on gate type, width, slope, and whether it’s automated. Call (888) 853-9043 for a free written estimate tailored to your property.
Is it cheaper to repair or replace a gate?
Repair is almost always cheaper when the gate panel, posts, and pier are sound and the failure is in the operator or wiring – often a few hundred dollars instead of a few thousand. Replacement makes more sense when the structure itself is failing. Call (888) 853-9043 and we’ll tell you honestly which one applies.
How much does an automatic gate opener cost in Glendale?
Automated operators typically run $1,100 to $3,600 installed, depending on whether it’s a swing or slide system, the gate weight, and the brand. Safety sensors and access control are separate line items. Call (888) 853-9043 for an exact quote – estimates are free.
Do I need a permit to install a gate in Glendale?
Most cities require a permit when a gate installation involves new structural work such as piers, footings, or electrical, so check with the City of Glendale’s building department before work begins. We’ll walk you through what typically applies to your project at the estimate. Call (888) 853-9043 to set one up.
Can you install a gate on a sloped driveway in Glendale?
Yes. Sloped driveways are common in Glendale’s hills, and gates are installed on them regularly with hardware and rail systems built for the grade. The written estimate covers the slope-specific setup. Call (888) 853-9043 for a free on-site estimate.
Get Your Free Gate Installation Estimate in Glendale
Gate installation is a project where a clear estimate makes all the difference. We specialize exclusively in gates – installation, electric repair, and repair – and we work with the brands you’re likely to have or want: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Our technicians have up to 13 years of experience, and the price is set per job by the written estimate, with no surprise fees.
Call (888) 853-9043 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Tell us about your driveway, the gate you have or want, and whether you’re thinking manual or automated, and we’ll set up a time to walk the property and put the numbers on paper.
Written by the team at Glendale Gate Repair.
Pricing reflects the Glendale market as of 2026. Glendale Gate Repair offers free estimates – call (888) 853-9043.
What Our Customers Say
"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Dana Norris"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Carmen Mendoza"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Jessica Kim