Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Glendale?
Gate parts and welding in Glendale typically run $150 to $450 for common part replacements, while on-site welding repairs like hinge rewelds or post brackets usually fall between $200 and $650 per job. A full operator or control board swap on an electric gate lands higher, often $350 to $1,200 depending on the brand. Those are honest 2026 estimate ranges for the Glendale market – every job gets its own written price after we look at the gate, and the estimate is free.
Glendale is a gate town. Hillside lots in the Verdugo foothills lean on driveway gates for security, and dense blocks of shuttered properties in south Glendale depend on them for privacy. Our technicians have up to 13 years of experience working on the exact brands installed across the city, which means fewer wasted visits and more accurate estimates. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Common part replacements (rollers, hinges, latches, remotes): roughly $150-$450.
- On-site welding (hinge rewelds, post brackets, frame repair): roughly $200-$650.
- Electric gate parts – motors, boards, loop detectors, access panels: roughly $350-$1,200.
- Operator brand and automation type are the two biggest cost drivers.
- Every price is confirmed in a free written estimate before any work starts.
Gate Parts & Welding Cost Breakdown (2026)
These are typical Glendale ranges for common gate parts and welding jobs. The written estimate sets the final price once we’ve seen the gate, the brand, and the condition of the hardware in person.
| Job | Typical Glendale Range |
|---|---|
| Remote replacement and re-pairing | $75-$175 |
| Hinge, roller, or latch replacement (manual gate) | $150-$350 |
| Hinge rewelding or bracket reinforcement | $200-$450 |
| Slide gate track or roller carrier repair | $250-$550 |
| Electric gate motor or operator replacement | $450-$1,200 |
| Control board or circuit board replacement | $350-$900 |
| Loop detector or safety sensor install/repair | $250-$600 |
| Access control or keypad repair | $200-$500 |
| Full weld-out of a damaged gate section | $300-$650 |
| Automatic gate opener installation (new) | $1,200-$3,500 |
What pushes a job toward the top of a range
Brand and automation tier matter most. A Mighty Mule or Ghost Controls operator is a simpler residential system, and parts and labor are usually lower. A FAAC, BFT, or DoorKing setup is commercial-grade hardware, so the operator, board, or access panel often costs more and takes more time to swap. Gate weight and material play a role too: a heavy wrought-iron swing gate needs sturdier hinges and stronger welding than an aluminum tube gate. And access matters – a hillside driveway off a narrow street in Glendale takes longer to reach and stage than a level property. Rarely is the gate itself the problem; it’s the hardware around it and how much of it has worn out.
What Affects Gate Parts & Welding Pricing in Glendale
- Brand of operator. We service nine brands – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – and knowing the actual unit means we diagnose it instead of guessing. Matching the correct part is the biggest single cost factor on any electric gate job.
- Residential vs. commercial-grade hardware. A Mighty Mule or Ghost Controls residential operator runs cheaper to repair than a FAAC or DoorKing commercial system. We work on both tiers, so the estimate reflects what’s actually on the gate, not a one-size-fits-all number.
- Gate material and weight. A heavy iron or steel gate stresses hinges, welds, and the operator’s motor harder than a lighter aluminum one. Welding on thicker steel takes longer and more material, which shows up in the estimate.
- Type of automation. Swing gates need different operators and arms than slide gates. A slide gate with a worn track or failing roller carrier often needs both mechanical and electrical work, and that adds scope.
- Site access and parking. Narrow hillside driveways and tight streets around Glendale mean extra setup time. On a level property with clear access, the labor drops. We factor this in honestly rather than padding hours.
- Parts availability for the specific brand. Known residential brands have widely available parts. On an older commercial operator, a discontinued board may mean sourcing, which can add time and cost to the job.
One thing we’ll always say straight: if a gate is genuinely beyond saving, we’ll tell you. Repair or replace – we’ll tell you honestly which one makes sense for your gate, rather than selling you a weld that won’t hold.
How to Save on Gate Parts & Welding
A gate that’s fixed early and correctly usually costs less than one left to fail. Here’s what actually keeps Glendale gate costs down.
- Get the free estimate first. A written estimate tells you exactly what’s wrong and what it costs before anything starts. Call (888) 853-9043 and we’ll come out with the same range you see above, then lock in the number in writing.
- Repair before the failure spreads. A squeaky hinge or a loose bracket caught early is a re-weld; ignored, it can crack the frame and add a whole repair on top. Small fixes stay in the lower ranges.
- Know your brand. Telling us up front it’s a LiftMaster, FAAC, or DoorKing saves diagnosis time and helps us source the right part the first time.
- Weigh repair against replacement honestly. If a single welded joint or a hinge is failing, repair is almost always the cheaper call. If the motor’s dead and the frame is bent, a new gate might save money in the long run – and we’ll say so.
- Bundle the small stuff. If the gate needs a re-weld and the latch is loose, handling both in one visit is cheaper than booking twice.
Every estimate is free and there’s no upsell – our technicians have up to 13 years of experience and know what lasts, which is why we quote honestly rather than throw parts at a gate.
Can You Fix a Broken Gate the Same Day in Glendale?
Many common gate repairs can be handled the same day in Glendale – remotes, hinges, latches, loop detectors, and control board swaps are often resolved in a single visit. It depends on whether the part for your brand is available and how much welding or access setup is needed. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Call (888) 853-9043 and we’ll tell you straight whether we can get to it today.
Do You Work on the Brand of Gate Operator I Already Have?
Yes. We work on the brand you already have – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Because we know each unit, we diagnose the actual brand installed instead of forcing generic parts into it. That matters on commercial-grade FAAC and DoorKing systems, where a wrong part can mean a second visit. If your unit isn’t on that list, call and describe it – we’ll be honest about whether we can help.
Is It Cheaper to Repair or Replace a Gate?
Repair is almost always cheaper when the gate frame and hardware are sound and only a hinge, bracket, weld, or single part has failed. Typical one-off repairs run $150-$650. Replacement makes sense when the frame is bent, the operator is dead, and the welds won’t hold – a new installed gate runs $1,200-$3,500 for the automation alone. We’ll tell you honestly which one makes sense for your gate. Call (888) 853-9043 for a free estimate.
Does Welding a Gate Require a Permit in Glendale?
A weld repair on an existing gate usually doesn’t need a permit, though new gate structures and electrical changes can require one – so ask the city’s building department before anything structural goes in. Any work touching the operator’s electrical supply or access wiring should be done by a trained technician. Call (888) 853-9043 and we’ll walk through what your job needs.
How Does Glendale’s Climate Affect Gate Hardware?
Glendale’s dry summers and mild winters put gate hardware through more than people expect. The sun bakes paint on iron and steel gates, and once that coating fails, rust starts on the welds, hinges, and brackets first. Seasonal heat also stresses the operator and control board, and dust from nearby hillside lots gets into tracks and loop detectors. Regular hardware checks keep small failures from turning into welding jobs. If your gate is in the Glendale hillside areas, the sun and slope stress it particularly hard.
Why Choose a Gate-Only Specialist for Parts and Welding
Gates are the only thing we do. Not fences, not garage doors, not general handyman work – gate repair, electric gate repair, and gate installation. That single focus means our technicians carry the right parts, know the brands on your gate, and finish jobs from diagnostic to done instead of turning a control board problem over to someone who’s never touched one. We cover the full arc of a gate’s life, from a first hinge swap and weld to an upgrade to automation, so you don’t need a second vendor when the gate moves to the next stage. Your gate, our only focus.
For the full picture of what we do across the city, see Glendale Gate Repair and our Glendale service page. Our technicians have up to 13 years of experience across residential and commercial gate systems, and it shows in a cleaner, tighter estimate.
How Much Does Automatic Gate Opener Installation Cost in Glendale?
Automatic gate opener installation in Glendale typically runs $1,200 to $3,500, depending on the operator brand and the gate’s weight and type. Residential-grade systems like Mighty Mule and Ghost Controls sit toward the lower end; commercial-grade operators such as FAAC, BFT, and DoorKing sit higher. If your gate is already automated, a parts repair usually costs far less than a full reinstall. Call (888) 853-9043 for a free on-site estimate – the written price is set per job.
What Kinds of Gate Parts & Welding Jobs Can We Handle in Glendale?
We handle the full range of gate parts and welding work for homeowners, residential property managers, and small commercial properties in Glendale:
- Hinge, roller, latch, and bracket replacement on swing and slide gates.
- On-site welding of hinges, post brackets, and damaged gate frames.
- Electric gate repair – motors, operators, circuit boards, remotes, and access control components.
- Loop detectors and safety sensor repair or replacement.
- Access control and keypad repair for gated driveways and shared entrances.
- New gate opener installation and upgrades to automation.
If your gate is manual, electric, or automated, call us at (888) 853-9043. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. The estimate is free, and we’ll tell you honestly whether repair or replacement makes sense.
What to Have Ready Before We Arrive
A little preparation keeps the estimate moving and can keep the price down. Have the brand of your operator ready if the gate is automated – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, or Mighty Mule. Note what’s failing: does the gate stick, drift, not latch, not open at all, or make a new noise? Clear access to the gate and any nearby parked cars so our technician can inspect the full swing or slide path. If you have the manual, have it handy. Knowing the exact model shortens diagnosis and gives you a more accurate number.
FAQs – Gate Parts & Welding Cost
How much does gate parts and welding cost in Glendale?
Gate parts and welding in Glendale typically costs $150 to $650 for common repairs, and $350 to $1,200 when a motor, control board, or access panel is involved. The written estimate after we inspect your gate sets the final price. Call (888) 853-9043 for a free estimate.
How much is a new gate motor in Glendale?
A new gate motor in Glendale usually runs $450 to $1,200, depending on the brand and whether it’s a residential Mighty Mule-style operator or a commercial FAAC or DoorKing system. Call (888) 853-9043 and we’ll confirm the number in a free written estimate.
Can you weld my gate on-site?
Yes, we can weld hinges, post brackets, and damaged frames on-site, typically $200 to $650 per job. On-site welding spares you removing the gate and hauling it to a shop. Call (888) 853-9043 to book a free estimate.
Do you repair gate parts for brands you listed, or only install new?
We repair and weld parts for the brand you already have, including all nine we service: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We also install new when replacement makes more sense. Call (888) 853-9043 for a free estimate.
Is it cheaper to fix my gate or replace it?
Fixing is almost always cheaper when only a part or weld has failed – typical repairs run $150 to $650 – while a full replacement and automation runs $1,200 to $3,500. We’ll tell you honestly which one makes sense for your gate. Call (888) 853-9043 for a free estimate.
Do you charge extra for same-day or urgent gate repairs in Glendale?
No – there’s no premium for same-day or urgent work. The price is set per job by the written estimate, whatever the timing. Call (888) 853-9043 and we’ll tell you what fits. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
What number do I call for a free gate repair estimate in Glendale?
Call (888) 853-9043 for a free gate repair estimate in Glendale. We’ll come out, look at the parts and welds, and write you a clear per-job price before any work starts. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Get a Free Gate Parts & Welding Estimate in Glendale
Whether it’s a wobbly hinge, a snapped weld, or a control board that won’t respond, we’ll tell you what’s wrong and what it costs before anything starts – and whether repair or replacement actually makes sense. We work on the brand you already have, from Mighty Mule and Ghost Controls up to FAAC, BFT, and DoorKing. Licensed and insured, upfront pricing, and a written estimate so you know the number in advance. Call (888) 853-9043 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Glendale market as of 2026. Glendale Gate Repair offers free estimates – call (888) 853-9043.
Written by the team at Glendale Gate Repair.
What Our Customers Say
"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Dana Norris"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Carmen Mendoza"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Jessica Kim